- (1) Soundstream PSW.124 12" 600 Watt Slim Shallow Car Audio Subwoofer SVC 4-ohm Sub
- (1) Rockville RXA-T1 1500 Watt Peak/375w RMS 2 Channel Amplifier Car Stereo Amp
- (1) Rockville RWK41 4 Gauge Complete Car Amp Wiring Installation Wire Kit with RCA's
- (1) Rockville RSST12 Single 12" 0.9 cu.ft. Sealed Car/Truck Shallow Sub Enclosure
- (1) Complete Single Sub Box Enclosure Installation Kit: Speaker Wire, Screws, Spades
Description:
Picasso Shallow Subwoofers combine performance and value. These shallow subwoofers accomplish their best sound in small sealed enclosures, with minimal power requirements, thanks to efficiencies in the cone and suspension design.
All enclosures should be made of .75” (3/4”) material only. When possible, make the baffle 1.5” (1 1⁄2) thick and add .75” (3/4”) to the depth of the enclosure to compensate. All volumes INCLUDE vent/port and subwoofer displacements. DO NOT change the volume unless you plan on adding a substantial amount of bracing. For added performance, applying a coat of fiberglass resin to the interior walls will greatly improve sealing the enclosure. Adding a thin layer of poly-fill will improve response by smoothing out reflections within the enclosure.
Features:
- Pressed Spruce Pulp Cone w/ Polypropylene Coating Protection
- High Density Polyether Foam Surround w/ UV & Chemical Protection
- 2.00” 4-Layer 4-ohm Voice Coil w/ Large Gauge Wire Increases Power Handling
- Nickel Plated 8ga Spring-Loaded Compression Wire Terminals
- Poly-Cotton Composite Suspension Dampen Violent Accelerations
- Formed Steel Subwoofer Frame with Black Powder Coat Finish
- 1-pc Gasket Trim Ring w/ Concealed Mounting Holes Included
- Stitched Voice Coil Leads Prevent Potential Damage
- High-Temperature Tolerance Adhesives Resist Thermal Failure
- 6mm T-Yoke & Top Plate Improve Low Frequency Dynamics
Specifications:
- Max Power: 600 Watts
- RMS Power: 300 Watts
- Efficiency (1w/1m): 84.0
- Voice Coil Configuration: 2″ SVC 4Ω
- Optimum Sealed ft3: 1.00″
- Optimum Ported ft3: N/A
- Vas (ft3): 1.58
- Cms (mm/N): .119
- Mms (g): 200.67
- Xmax (mm): 10
- Xmech (mm): 15
- Z (Ω): 4
- Impedance: 4Ω
Thiele/Small Parameters
- Re (Ω): 3.20
- Fs (Hz): 32.60
- Qes: .954
- Qms: 6.728
- Qts: .836
- Le (mH): 1.0274
- Diam: 12
- Vas (L): 1.58
- BL: 11.74
- Mms (g): 200.67
- Sen (db): 84.0
- Mounting Depth: 3.50″
Recommended Enclosures
- Optimum Sealed ft3: 1.00″
Sealed Enclosures
- Min. Airspace: 0.75 ft3
- Min. QTC: 1.47
- Min. Tuning (Hz): 40.2
- Opt. Airspace: 1.00 ft3
- Opt. QTC: 1.34
- Opt. Tuning (Hz): 37.4
- Max. Airspace: 1.25 ft3
- Max. QTC: 1.26
- Max. Tuning (Hz): 35.7
Check out this video of the 4 channel version of this amplifier:
Description:
Over the years, the technology used to create audio amplifiers has grown by leaps and bounds. We consider it our mission to use our expertise in developing the latest technologies and to bring you the absolute best sounding amplifiers on the market at a reasonable price. From its clean, sleek design to its high quality components, you will be amazed at the quality and power that these new Phenom amps offer.
The RXA-T1 is a 2 channel amplifier with 1,500 Watts peak output . You can also bridge the amplifier and get 1 x 370 Watts Dyno-Certified RMS @ 4 Ohms. Here at Rockville we offer the best value in car audio. We therefore want to make it easy for you to compare our products to any brands on the market. The peak rating can be used to compare with brands who use peak ratings such as Boss and Power Acoustik while the Dyno Certified RMS rating can be used to compare with top brands such as Kicker, Rockford, Alpine, etc.
This unit also features a high speed MOSFET power supply, studio-grade bipolar output stage transistors and ELNA brand audiophile capacitors. It has a fully adjustable 12dB/Octave cross over with differential circuitry. High Level inputs, also referred to as Speaker Level inputs, allow you to install the amplifier into your vehicle even if you do not have any preamp outputs available. That means you can install this amplifier to your factory or aftermarket receiver. Other features include Auto-Start Smart turn-on (This function senses when there is a signal from the head unit and automatically turns on the amplifier hence no need to run a Remote Turn-On wire), a fully adjustable 12dB bass equalizer, 2 channel / bridgeable mono model, mute and delay soft start technology, and a crossover band-pass control. The RXA-T1 is protected by a full IC controlled circuit and has professional peak limiter circuitry guaranteeing distortion free musical playback at all levels.
The circuitry of this amplifier is a class A/B circuitry. Class A/B is known to have amazing sound quality. Pro audio amps usually all are class A/B. Class A/B however is not known for its efficiency. To make this amplifier more efficient we simulated a class “G” amplifier. Class G is technology that switches the rail voltage depending on how much power is being used. We have similar technology built into these class A/B amplifiers which make these about 65-70% efficiency which is just amazing for a class A/B amplifier.
We are so confident that you will be extremely satisfied with this amplifier that we are giving every customer a 90 day money back guarantee. So purchase the amplifier and try it for 90 days. If you are not happy, we will call tag it and cover return shipping costs and refund you all your money back. (Amp must be complete with accessories and original box please).
Features:
- Rockville RXA-T1 1500 Watt Peak/370 Watt Dyno-Certified RMS 2 Channel Amplifier Car Stereo Amp
- Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc):
- 250 Watts (2 x 125 Watts) at 4 ohms and 1% THD+N
- 370 Watts (2 x 185 Watts) at 2 ohms < 1% THD
- 1 x 370 Watts bridged @ 4 Ohms < 1% THD
- Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc)
- 1500 Watts (2 x 750 @ 2 ohms or 1 x 1500 @ 4 Ohms)
- High-Speed MOSFET Power Supply
- Studio-Grade Bipolar Output Stage Transistors
- Fully Adjustable 12dB / Octave Crossover
- Low Pass Filter: 50Hz - 250Hz
- High Pass Filter: 15Hz - 250Hz
- Fully Adjustable 12dB Bass Equalizer with Differential Circuitry
- 2-Ohm Stable Stereo
- 4-Ohm Mono Bridgeable
- Mute and Delay Soft Start System
- Full IC-Controlled Protection Circuitry
- RCA Preamp Line Output
- ELNA Brand Audiophile Capacitors
- 8 Volt Preamp Circuitry
- Status Mode LED Indicator
- High Level Input with Smart Auto Turn-On
- Minimum THD at Rated Power: < 0.05%
- Frequency Response: 10Hz - 40KHz
- Damping Factor: > 200 @ 100Hz
- 50 Amp Maxi Fuse
- Dimensions: (W x H x L) 8.5" x 1.8" x 13"
About Rockville Quality Control Procedures:
The Rockville brand stands for Quality, Innovation and Value. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All user functions are tested and all internal components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to their factory to quality control every line of production. During production every product is tested and on top of that Rockville goes the extra mile and has their high level product engineers do an additional quality control. They test a certain percentage of all products from the production line a second time to ensure that the quality meets their vigorous standards, and to make sure that there is never a batch of products with even a slight problem. All Rockville sub enclosures are backed with a full 90 day warranty, though it is unlikely that you will need to use it.Video of RWK41:
Unboxing Video for RWK41:
Description:
The Rockville RWK41 4 AWG (American Wire Gauge) amp kit has the following differences over other amp kits on the market at this price point.
1. Our RCA cables are 100 % copper. These are top of the line RCA cables
2. Better Resistance: The only thing that really matters with wires is the resistance rating. This is a measurement of conductivity and how much signal is loss per foot of wire. Since Rockville wires are made with around 3 times as much copper as any other wire at this price point, these wires had a much better resistance rating which means they will transfer more power to your amps than the other brands.
3. We do not cheat you on the thickness of the wire. These are standard American wire gauge thickness. This is another reason our conductivity is better than anything else at this price point. Other brands in the market place write 4 gauge, but cheat you on the thickness. We are honest about the thickness.
4. The Rockville amplifier installation kits feature a new soft abrasion proof insulating jacket. This rugged PVC outer jacket allows for 100% improved flexibility over standard power cables making them extremely easy to route through your vehicles interior, and it maintains exceptional resistance to grease and oil. The PVC outer jacket can with-stand an extreme temperature range of -40 to 220 degrees F.
The RCA signal transfer cables included in this kit feature blue and silver twisted pair technology in a clear outer jacket insulation skin. Not only do the blue and silver wires look cool but they also provide superior signal transfer with maximum noise suppression. They are 100% copper to provide absolute lossless perfect signal transfer to your receiver. This technology reduces interference, so your audio signal flows clean and pure at all power levels.
This kit also includes a massive 60 Amp AGU Gold Plated Fuse, so you can be sure it will handle the all the DC power that your amp will need without even the slightest loss of current. The included 7 split loom tube provides protection for your power cable from the typically harsh environment found under the hood of your car.
Audiosavings product experts have tested this amp kit against many leading amp kits on the market and were were impressed not only by the great looks but by the quality of these Rockville installation kits as well. These kits had a lower resistance rating than the other brands we compared and tested them against. What this means is that Rockville manufactures their kits with more copper than other kits at this price point, ultimately providing your amplifiers with better and cleaner DC power, so they work cooler and more efficiently. You will hear the difference a Rockville installation kit will make!
Features:
- 1 – 17’ High Grade Twisted Pair of 100% Copper RCA Cable
- 17’ – 4 Gauge Translucent Blue SuperFlex Power Cables
- 17’ – 18 Gauge Blue Remote Cable
- 17’ – 16 Gauge Clear Speaker Wire
- 3’ – 4 Gauge Clear SuperFlex Ground Wire
- Gold Plated AGU Heat Resistant Fuse Holder
- 60 Amp AGU Gold Plated Fuse
- 7’ Split Tube Loom
- Accessories Included: Wire Ties, Ring Terminals, Butt Connectors, Spades, and Grommets
Description:
The RSST12 single 12" sealed shallow mount speaker box is made in the USA with Grade “A” 5/8" MDF wood. This enclosure is made with precision cutting machinery by industry experts that have been making these enclosures in the USA for over 20 years. All Rockville enclosures come with a customized enhanced glue that is unmatched by any other manufacturer. That means that the carpet will stay in place and not rip or tear. The 5/8" USA MDF is much stronger then any type of import wood. This will keep your box performing at an optimal level by not flexing and distorting your woofers. Your woofers will thank you! EVERY Rockville enclosure is not only glued at all joints but stapled as well. If that wasn’t enough we add a layer of silicon to every seam! This makes your Rockville enclosure rock even more!
MADE IN THE USA WITH PRIDE!
Features:
- Rockville RSST12 Single 12" 0.9 cu.ft. 5/8" MDF Sealed Truck Subwoofer Enclosure Box
- Proudly Made In The USA, Using Only The Finest Quality Materials - For The Best Level of Performance From Your Subs!
- Designed For 12" Shallow Mount Subwoofers
- Machine precision cut mounting holes
- 5/8" USA Heavy Duty MDF Construction
- Top of the line Glue for extra durable adhesion
- High quality GOLD spring loaded terminals
- Designed, tested, and engineered to work perfectly with high powered subs
- Designed to give the best sound quality
Enclosure Measurements:
- Type of Enclosure: Sealed Truck/Shallow
- Enclosure Sub Size: Single 12" Shallow
- Dimensions in Inches: 20" (L) x 7.5" (Bottom Depth) x 5" (Top Depth) x 15"
- Top and Bottom Depth: 15"
- Mounting Depth: up to 6" (enough depth for any shallow sub on the market)
- Gross Volume Per Sub (Measurement for the outer dimensions of the box): 1.1 Cubic Feet
- Net Volume Per Sub (Measurement for the outer dimensions of the box less the thickness of the wood): 0.9 Cubic Feet
About Rockville Quality Control Procedures:
The Rockville brand stands for Quality, Innovation and Value. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All user functions are tested and all internal components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to their factory to quality control every line of production. During production every product is tested and on top of that Rockville goes the extra mile and has their high level product engineers do an additional quality control. They test a certain percentage of all products from the production line a second time to ensure that the quality meets their vigorous standards, and to make sure that there is never a batch of products with even a slight problem. All Rockville sub enclosures are backed with a full 90 day warranty, though it is unlikely that you will need to use it.Complete Single Subwoofer Enclosure Installation Kit!
Includes:
- 10 Drywall Wood Screws (Wood screws are the type of screws; the screws are actually made of metal)
- 12 Feet of 14 AWG Blue Speaker Wire
- 2 Spade Terminals
This accessory package includes everything you need to install one subwoofer into an enclosure, and wire to connect the enclosure to your amplifier. This package is a top of the line accessory package which we put together and tested.
The drywall wood screws were hand selected by our installation experts because they drill into the enclosure very cleanly, without chipping the enclosure. The speaker wire is 14 gauge. This is way better than using 16 gauge. You can be 100 % sure that your enclosure will have a clean signal to the amplifier with this top of the line speaker wire. These spade terminals have also been hand selected by our installation experts to make the internal wiring simple, secure, and to run the audio signal cleanly.
- UPC:
- 613817050917
