Package Includes:

• (2) Power Acoustik MOFO-154X 15" 3000 Watt Car Audio Subwoofer DVC 4-Ohm Sub
• (1) Rockville KRYPTON M4 6000w Peak/1500w RMS Mono 1 Ohm Car Amplifier Amp+Remote
• (1) Rockville RWK01 0 Gauge Complete Car Amp Wiring Installation Wire Kit w/ RCA's
• (1) Rockville RD15 Dual 15” 2.1 cu.ft. 3/4" MDF Sealed Car Sub Enclosure Box USA
• (1) Dual Sub Box Enclosure Installation Kit: Speaker Wire, Screws, Spade Terminals

---

Description:

MOFO-X subwoofers are refined and increase efficiency dramatically! MOFO subs use a composite sandwich cone with a polypropylene surface for durability and Spruce pulp backing for smooth low bass. Like the original MOFOs, the new models still use an aluminum dust cap that couples to the voice coil former and extends over the cone. Why? The fins brace the cone and eliminate cone flex during high excursion. And since they are aluminum and couple to the voice coil, they act as a heatsink or heat extractor. Using the latest materials, the new MOFO subs yield superior performance. Cast aluminum baskets? Of course! Increased bottom octave output? You Bet! Louder than the original design? Duh!!

Cast Aluminum Heatsink
The anodized blue dust cap on the MOFO subwoofer looks cool and also serves a specific purpose. Because the dust cap is coupled to an aluminum voice coil former, it acts as a heatsink, extracting heat away from the voice coil, keeping it cool.

Non-Pressed Pulp Cone
Ask any sound quality enthusiast what woofer cone material they prefer, and they will all say PAPER. With that in mind, we used a beefy non-pressed pulp paper cone. The aluminum dust cap fits into the recesses of the cone for additional bracing.

Features:

• Overcompensating Motor Structure for Increased Magnetic Strength
• 12mm T-Yoke & Top Plate Improve Low-Frequency Dynamics
• Vented T-Yoke & Frame Reduces Voice Coil Heat Build-up
• Die-Cast Aluminum Heat Sink Dust Cap Absorbs Voice Coil Heat
• Aluminum Dust Cap Fins Dissipate Heat & Strengthen Cone
• Non-Magnetic Non-Resonate Die-Cast Aluminum Frame
• 2.5” 4-Layer Voice Coil w/ Large Gauge Wire Increases Power
• High-Temperature Tolerance Adhesives Resist Thermal Failure
• Nickel Plated 8ga Spring-Loaded Compression Wire Terminals
• Non-Transfer Spruce Pulp Cone w/ UV & Chemical Protection
• High-Density Polyether Foam Surround w/ UV & Chemical Protection
• Dual Poly-Cotton Suspension Dampen Violent Accelerations
• Stitched Voice Coil Leads Prevent Potential Damage
• 1-pc Gasket/Trim Ring w/ Concealed Mounting Holes Included

Specifications:

• Max Power Handling: 3,000 Watts
• RMS Power Handling: 1,700 Watts
• Efficiency (1w/1m): 86.90
• Voice Coil Configuration: 2.50? Dual 4O
• Motor Volume: 373oz
• Mounting Depth: 8.125?
• Optimum Sealed Enclosure ft3: 2.00
• Optimum Ported Enclosure ft3: 4.00

Enclosure Recommendations

All enclosures should be made of .75” (3/4”) material only. When possible, make the baffle 1.5” (1 1/2”) thick and add .75” (3/4”) to the depth of the enclosure to compensate. All volumes INCLUDE vent/port and subwoofer displacements. DO NOT change the volume unless you plan on adding a substantial amount of bracing. For added performance, applying a coat of fiberglass resin to the interior walls will greatly improve sealing the enclosure. Adding a thin layer of poly-fill will improve response by smoothing out enclosure.

Sealed Enclosure

• Cubic Feet: 2.00
• Tuning Frequency: 40

Ported Enclosure

• Cubic Feet: 4.00
• Port Diameter: 4" x 11.75"
• Tuning Frequency: 35.6

Driver Parameters

• FS (Hz): 24.4
• QMS: 5.95
• VAS (ft3): 4.077
• X-MAX (mm): 15
• X-MECH (mm): 23
• QES: 0.51
• RE (O): 7.23
• BL (Tesla): 26.3
• RMS Power: 1,700
• MAX Power: 3,000
• QTS: 0.47
• SPL (1w/1m dB): 87
• Voice Coil: DVC 4O

Physical Dimensions

• Overall Diameter: 15.5"
• Overall Height: 9.25"
• Mounting Depth: 8.125"
• Cutout Diameter: 14.125"
• Motor Diameter: 7.875"
• Motor Height: 3.00”
• Flange Width: 0.75”
• Flange Height: .625"
• Weight: 30lbs.??

---

Krypton Series (Product Video):

What's in the Box:

• Amplifier
• 150A External fuse
• Bass Remote with clipping indicator
• Birth sheet with tested power
• Owner’s manual
• Mounting Screws
• Warranty

Description:

The Krypton series of amplifiers by Rockville are engineered to have the best reliability and features. Whether you are a car audio competitor or just like to enjoy loud music. We engineered and designed these amps from the ground up to give you great sound quality and great features. You will notice the cool battery voltage display meter which looks great but also serves as a tool for you to know if your battery voltage is dropping which would affect your systems performance. We designed the amps to be able to last for many years even if you are playing them at max volume before clipping for extended periods of time.

Our favorite feature we introduced of the Krypton series is the bass remote that has a clipping indicator. This allows you to set the amp to max output before clipping on any song. This will protect your subs while you maximize SPL. What is nice about this is that you can set the gain level to max before clipping on any given song in real time! If you use a DD-1 or another tool, you are setting the gain on one song but the next song might have more headroom or might clip depending on the levels it was recorded at (this is referred to as crest factor in the engineering world).

We guarantee that this series of amplifiers will not only meet their Dyno Certified power but exceed their rated power.

Another feature we love about this is the bass equalizer. Most amps have this feature however not all bass EQ are created equal. Some bass EQ's will just clip your subs to death. Our bass EQ circuitry will boost the proper frequencies in a way that sounds good and is safe for your subs. In addition you can always use the clip indicator on the bass remote to make sure you are not sending a clipped signal to your subs. Our amplifier is meant to give you as much clean power to your subs as possible. Our voltage display allows you to make sure you are getting the proper voltage to your amp and our clip indicator on the remote will make sure you always send clean power to your subs. In addition we also guarantee the amplifier will be giving over the rated Dyno Certified so you can confidently match our amplifier with high-end subs and know what to expect!

What about sound quality and efficiency though ??
Well glad you asked. This amplifier is engineered so well that it has an extremely low signal to noise ratio which just means the sound will be super clean even at high volume levels. It also has a good efficiency rating so you don't have to draw too much power from your battery. One other thing that is important is that we engineered this to have a high common mode rejection rating (CMRR). This means that the amp has the capability to block out engine noise signals. By rejecting unwanted noises the end result is the cleanest sound quality.

Once again, Rockville has stepped up its game with the all new Krypton series. Their is no other amp like it on the market. In our opinion this is the best budget series of amps in the world. We actually enjoy this amp more then others that cost over 2 times the price.

Features:

• Rockville Krypton-M4 6000 Watt Peak / 1500w Dyno-Certified RMS Mono 1 Ohm Car Amplifier Amp
• Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc)
  
  • 1 Ohm: 1500 Watts x 1 Channel <1% THD+N (76% efficient)
  • 2 Ohm: 1000 Watts x 1 Channel <1% THD+N (86% efficient)
  • 4 Ohm: 550 Watts x 1 Channel <1% THD+N (89% efficient)
• Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc)
  
  • 1 Ohm: 6000 Watts x 1 Channel
  • 2 Ohm: 4000 Watts x 1 Channel
  • 4 Ohm: 2200 Watts x 1 Channel
• Digital Voltage Display on Amp (Accurate within 0.15V)
• Power/Protect/Clip LED Indicators on the front panel
• Power/Protect/Clip LED Indicators on Remote control
• Clip indicator on the bass remote allows you to quickly set any song to right before clipping in real time
• Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
• Low Pass Filter: 50Hz - 250Hz
• Subsonic Filter: 15Hz - 55Hz
• Fully Adjustable 12dB Bass Equalizer
• Remote Dashboard Subwoofer Control
• 8 Volt Preamp Circuitry
• Phase Control Switch
• High-Speed MOSFET Power Supply
• Optical Coupler Class “D” Technology
• Full IC-Controlled Protection Circuitry
• Mute and Delay Soft Start System
• RCA Preamp Line Output
• Status Mode LED Indicator
• Minimum THD at Rated Power: <0.1%
• S / N Ratio: >90dB
• Frequency Response: 15Hz - 250Hz
• Damping Factor: >150 @ 100Hz
• 150A External Fuse Included
• Passes the Signal Burst Test (Instant signal for full power “SPL Contest”)
• Rockville engineered with a super low signal to noise ratio to give you clean sound
• Improved Bass EQ filter works well to boost the proper frequencies
• Dimensions: (W x H x L) 16.29? x 8.66? x 2.2?

---

Video of RWK01:

Description:

The Rockville RWK01 0 AWG (American Wire Gauge) amp kit has the following differences over other amp kits on the market at this price point.

1. Our RCA cables are 100 % copper. These are top of the line RCA cables

2. Better Resistance: The only thing that really matters with wires is the resistance rating. This is a measurement of conductivity and how much signal is lost per foot of wire. Since Rockville wires are made with around 3 times as much copper as any other wire at this price point, these wires have a much better resistance rating which means they will transfer more power to your amps than the other brands.

3. We do not cheat you on the thickness of the wire. These are standard American wire gauge thickness. This is another reason our conductivity is better than anything else at this price point. Other brands in the market place write 4 gauge, but cheat you on the thickness. We are honest about the thickness.

4. The Rockville amplifier installation kits feature a new soft abrasion proof insulating jacket. This rugged PVC outer jacket allows for 100% improved flexibility over standard power cables making them extremely easy to route through your vehicles interior, and it maintains exceptional resistance to grease and oil. The PVC outer jacket can with-stand an extreme temperature range of -40 to 220 degrees F.

Features:

• Rockville RWK01 0 AWG (American Wire Gauge) Complete Car Amp Installation Wire Kit
• 17’ – 0 Gauge Translucent Blue SuperFlex Power Cable
• 3’ – 0 Gauge Translucent Black SuperFlex Ground Cable
• Gold Plated ANL Heat Resistance Fuse Holder
• 200 Amp ANL Gold Plated Fuse
• 1 – 17’ High Grade Twisted Pair of RCA Interconnects
• 25’ Translucent Blue Speaker Wire
• 7’ Split Loom Tubing
• 17’ Amplifier Remote Turn On Cable
• Wire Ties and Ring Terminals, and all other accessories you need for a clean installation
• Soft abrasion proof insulating jacket allows for 100% improved flexibility
• PVC outer jacket can with-stand an extreme temperature range of -40 to 220 degrees F

---

Description:

The RD15 dual sealed speaker box is made in the USA with Grade “A” ¾” MDF wood. This enclosure is made with precision cutting machinery by industry experts that have been making these enclosures in the USA for over 20 years. All Rockville enclosures come with a customized enhanced glue that is unmatched by any other manufacturer. That means that the carpet will stay in place and not rip or tear. The ¾” USA MDF is much stronger then any type of import wood. This will keep your box performing at an optimal level by not flexing and distorting your woofers. Your woofers will thank you! EVERY Rockville enclosure is not only glued at all joints but stapled as well. If that wasn’t enough we add a layer of silicon to every seam! This makes your Rockville enclosure rock even more!

MADE IN THE USA WITH PRIDE!

Features:

• Rockville RD15 Dual 15" Sealed Subwoofer Enclosure
• Proudly Made In The USA, Using Only The Finest Quality Materials - For The Best Level of Performance From Your Subs!
• 3/4" USA Heavy Duty MDF Construction
• Machine precision cut mounting holes
• Top of the line Glue for extra durable adhesion
• Designed, tested, and engineered to work with most of today’s popular woofers. These enclosures are built with the quality additives needed to maximize the performance of any sound system.

Enclosure Measurements:

• Type of Enclosure: Sealed
• Enclosure Sub Size: Dual 15"
• Dimensions in Inches: 16.75" L x 36" W x 16.25 H"
• Top and Bottom Depth: 16.75"
• Mounting Depth: up to 15.5" (enough depth for any sub on the market)
• Gross Volume Per Sub (Measurement for the outer dimensions of the box): 2.7 Cubic Feet
• Net Volume Per Sub (Measurement for the outer dimensions of the box less the thickness of the wood): 2.1 Cubic Feet

---

About Rockville Quality Control Procedures:

The Rockville brand stands for Quality, Innovation and Value. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All user functions are tested and all internal components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to their factory to quality control every line of production. During production every product is tested and on top of that Rockville goes the extra mile and has their high level product engineers do an additional quality control. They test a certain percentage of all products from the production line a second time to ensure that the quality meets their vigorous standards, and to make sure that there is never a batch of products with even a slight problem. All Rockville sub enclosures are backed with a full 90 day warranty, though it is unlikely that you will need to use it.

---

Complete Dual Subwoofer Enclosure Installation Kit!

Includes:

• 20 Drywall Wood Screws (Wood screws are the type of screws; the screws are actually made of metal)
• 20 Feet of 14 AWG Blue Speaker Wire
• 4 Spade Terminals

This accessory package includes everything you need to install two subwoofers into an enclosure, and wire your enclosure to your amplifier. This package is a top of the line accessory package which we put together and tested.

The drywall wood screws were hand selected by our installation experts because they drill into the enclosure very cleanly, without chipping the enclosure. The speaker wire is 14 gauge. This is way better than using 16 gauge. You can be 100 % sure that your enclosure will have a clean signal to the amplifier with this top of the line speaker wire. These spade terminals have also been hand selected by our installation experts to make the internal wiring simple, secure, and to run the audio signal cleanly.