WAIT!

What's in the Box:

• Amplifier
• Birth sheet with Dyno-tested power
• Mounting Screw Kit
• Owner’s manual
• Warranty

Description:

The all new ATOM full range class “D” series of amplifiers produce a ton of power while delivering pristine sound quality. We also include a volt meter on this series.

The ATOM P60 is a class D 2-Channel high power amplifier with 4800 watts peak output and 1200 watts true RMS power. The RMS power is tested on a dyno using the certified run. It puts out 600 watts x 2 channels at less than 1% THD at 14.4 volts. We give the true power and the peak rating so you can easily compare this amp to any brand on the market regardless of how they like to rate their products.

This amp utilizes high grade marine components including a conformal coated PCB board with a waterproof glue that is painted on to protect the circuitry. The heat sink casing, including the bottom plate, is made of stainless steel which is rustproof. The end panels, the internal mounting screws and hardware of the amp are made of stainless steel and are rustproof as well. Even after many years of use the amp will be rust free and operate like new!

Features:

• Rockville ATOM P60 4,800 Watt Peak and 1200 Watt RMS Class D 2 Ohm Car Stereo Amplifier Dyno certified RMS Power (less than 1 % distortion) (Use these ratings when comparing with other premium brands such as Kicker, Rockford Fosgate, etc)
• 2 Ohm: 600 Watts x 2 Channel <1% THD+N @ 14.4 Volts
• 4 Ohm: 360 Watts x 2 Channel <1% THD+N @ 14.4 Volts
• 4 Ohm Bridged: 1200 Watts x 1 Channel <1% THD+N @ 14.4 Volts
• Peak Power: (Use these ratings when comparing with great budget brands such as Boss, Power Acoustik, Crunch, etc)
• 2 Ohm: 2400 Watts x 2 Channel
• 4 Ohm: 1440 Watts x 2 Channel
• 4 Ohm Bridged: 4800 Watts x 1 Channel
• Digital Voltage Display on Amp
• Adjustable Low Pass Filter: 50Hz – 250Hz
• Adjustable High Pass Filter: 50Hz – 250Hz
• Painted Conformal Coating PCB Board (Uses 2577 Waterproof Glue)
• Rustproof Aluminum heat sink with black hairline finish
• Stainless steel end panels are rustproof
• All screws and mounting hardware are stainless steel and rustproof
• Bottom panel is aluminum and rustproof
• 4 Gauge power and ground terminals
• 10 Guage speaker wire temrinals
• All channels on the amp have crossovers so they can each be used for subs or full range speakers or tweeters or midrange speakers
• All channels on the amplifier are bridgeable
• High-Speed MOSFET Power Supply
• Under Voltage Protection at 10V
• Over Voltage Protection at 16V
• Tertiary Supplies Circuitry
• Studio-Grade Bipolar Output Stage Transistors
• Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
• Full IC-Controlled Protection Circuitry
• Fully Adjustable 12dB Bass Equalizer
• Adjustable Input Level Control
• Mute and Delay Soft Start System
• 8 Volt Preamp Circuitry
• Status Mode LED Indicator
• Minimum THD at Rated Power: < 0.05%
• S / N Ratio: >90dB
• Frequency Response: 10Hz - 30KHz
• Damping Factor: >85 @ 100Hz
• 40 Amp x 3 ATC Fuse
• Dimensions: (Lx W x H) 12.4˝ x 6.7˝ x 2.0˝